Posts Tagged ‘cycling’

I don’t think bike commuting helps make friends in every city or community but it sure helps here.  Using my bike almost exclusively for transportation in the city of Memphis makes me a bit of a novelty.  Given that midtown Memphis is a pretty diverse place and there are a lot of bike commuters, I’m also not hated for being one that impeeds traffic.

Almost everywhere I go, people talk to me about commuting on a bike.  I have people at intersections roll down their window, usually to ask me a question about why I’m out on a bike.  I just started at a new gym and while very few people want to talk at 6:30am, the fact that I walk in wearing a bike helmet seems to be a great conversation starter.  Sure, most conversations center around the weather for that day but at least people feel compelled to interact with me.  These situations just confirm my belief that bike commuting makes for stronger communities by stimulating people to interact with each other.

I love the ease of use of my Crank Brothers Eggbeater pedals.  I’ve used them extensively for off- and on-road purposes.  Mud clearance, ease of engagement, ease of clipping out and range of motion are incomparable.  Customer service has also been responsive and informative.  However, I have experienced numerous failures with Crank Brothers pedals.  I have had the spring break, end-bolt disappear, cage bent, cleat fail and other miscellaneous failures.  I’ve even started to have a collection of old pedals where one broke and I keep the other for replacement of future failures.  It isn’t always the same-side pedal so it’s not something funky I’m doing with one leg.

I believe the cleats are designed to fail before the pedal as they’re made of a pretty soft metal.  However, in my experience, they tend to last as long as the pedal.  Overall, I think Crank Brothers pedals are very comfortable to use but have average or below-average durability.

Here are several tips if you use Crank Brothers pedals:

1.  Don’t buy the Smarty pedal.  It’s worthless.  It may fail almost immediately.

2.  Inspect your pedal and cleats regularly after 1000 miles (assuming your an urban commuter).  You don’t want a catastrophic failure to occur when you’re hopping a curb.

3.  Only buy the pedals which have forged cages.  The Smarty and others have a stamped cage that is weak at best — must be built in China.  However, don’t blame it on China.  The designer, in this case Crank Brothers, tells the manufacturer what to make.  The design responsibility lies with Crank Brothers.  They only make what Crank Brothers tells them to make.

4.  Save your old pedals.  You’ll likely want to buy more Crank Brothers pedals because of how easy they are to use but if you ride a lot, the pedals will fail and you’ll need a spare.

A User Need for Crank Brothers:

I want pedals and cleats that will last  5 grand of urban commuting yet are still as comfortable to use as your current designs.

A lot, I think. Following is a list of the repairs/maintenance I performed during 30 days in July and August:

Monday 7/20: Repaired tube. 15 minutes.
Tuesday: Cleaned both brake cables and replaced cable housing on front brake – 45 minutes.
Saturday 7/25: Repaired three tubes – 40 minutes.
Sunday: Repaired tube with two punctures – 30 minutes.
Tuesday: Puncture. 5 minute road repair, 15 min. patching work
Sunday: Trip to bike store, Replaced brake calipers, mounted new light, tightened bottom bracket on the fixie – 2.5 hours $25
Tuesday: New seatpost – the old one was almost 12 years old – 45 minutes $19
Saturday: Rebuilt front wheel – rim was almost 12 years old and out-of-round. $70 rim and spokes. – 2 hours
Sunday: Switched out rear tube to a Slime tube – other tube had six patches: 15 minutes
Friday 8/14: Fixed cable and adjusted internal hub shifter cable that was completely not functional: 20 minutes (still need to zip tie the cable to the frame and I noticed the cable is frayed at the shifter – will need to replace.)
Saturday 8/15: Biffed it on the fixie. Lots of time doctoring wounds. Have a nicely bent rear wheel. Will need 45 minutes to true. (Not included in the calculation)

For July/August 30 days: 8.25 hours of repairs.

This seems like a lot of time to be spending maintained a fleet of bikes as my primary form of transportation. I don’t wonder long about whether many of our current population would be interested in spending this much time repairing their primary form of transportation. We need more dependable bikes with more durable components!!!!!!!!!!!!

My Miles (estimate):

1. To Work: 17mi/day*260days= 4420mi
2. Farmer’s Market: 13mi*20 = 260

3. Misc. rides to store:  52*10= 520

4. Critical Mass:  10*13= 130

Total Mileage:  5330

My Bikes:

1.  Circa 1997 Schwinn Homegrown converted to single speed with knobby street tires (work commuter)

2. 2005 Breezer Citizen 3-speed with trailer bike and child-car attachments (grocery getter)

Things I Bought for Biking (that I can remember)*:

2 pairs of shorts (baggies), Two poly shirts, 3 pairs of socks, 2 chains, 2 pairs of pedals, numerous tubes and patch kits, 1 pair cranks, 1 bottom bracket, one rigid fork (the suspension was warn out), 2 rear tires (my front tire is about 5 years old and has about 8000 miles), 1 saddle, 2 rear lights, 2 front lights, two boxes gauze pads, 2 boxes band aids, two rolls medical tape, 1 tube of triple antibiotic goo, 1 pump, 1 rear hub rebuild kit, 1 single speed conversion kit, 1 brake cable kit, 2 sets of brake pads, 1 set of brake levers, repair of internal hub (I messed it up trying to adjust it), one rear fender, reflective tape, 1 pair shoes (my others were 6 years old)

Keep in mind that this was not my first year of commuting.  Most of these purchases were required just to maintain the bikes.

* Does not include cash purchases

Total Cost:  $1358.49

At Brooks Museum in Overton Park. See:

http://www.bicyclefilmfestival.com/